hayward flow switch troubleshooting

You can test the continuity of the flow switch using a Voltmeter or Ohmmeter. The Hayward Aqua Trol is a saltwater generator for above ground pools.

Heatpump Troubleshooting Manualzz

The control checks for open Blower Vacuum Switch 2.

. Check out the Sundance Spas Flow Switch Replacement if you are looking for the flow switch replacement for your Sundance Spa Jacuzzi. Step 1 Turn the unit off and unplug it from the power source for 30 seconds. This generic replacement for the Hayward Goldline flow switch is relatively easy and will quickly fix your no-flow problem.

Step 1 Power LED not on. Check for possible turbulence inside of flow T. USB drive must already be connected to your computer.

GLX-FLO-RP Flow switch is factory original The GLX-FLO-RP screw into your existing tee and comes with a 15 cord. So if you are having issues it may be a manufacturer error or misprint just try turning the opposite way. This did the trick and I didnt recieve the NO FLOW message.

Check that the flow line is plugged all the way into the control box. Continuity is open if there is no flow. HAYWARD No LEDsLCD display verify 220-240 VAC or 115-125 VAC at input terminal TBI.

The arrows at the top of the hex nut need to point in the same direction as the water flow. If you need help troubleshooting the device read our helpful guide with the most frequently asked questions and answers. Darrin - If you held the switch contacts closed for 60 seconds and the No Flow LED did not go off your new switch may be bad.

The blower will turn off for one second. There should be no elbow after the flow switch. Within the options menu select Save link as Note.

Gas valve opens and monitors flame sense. Start by pressing the Diagnostics button two times. To view these documents you will need to download the free Acrobat Reader.

The reading should now reflect the average salt level. 3200 t -15 t -3 t -9 1Step 2 Step 3 Step 4 How to. The Control checks for a closed Blower Vacuum Switch.

The flow switch requires a minimum flow rate of 11 GPM to consistently stay closed. This resets the spas control panel and will make the switch work again. Start with the main toggle switch in the Auto position.

Repeat until display shows correct cell. Blower starts pre-purge cycle as the igniter heats up 20 Sec. Flow Switch Assembly GLX-FLO-RP for HaywardGoldline Aquarite Salt Systems Pool Flow Sensor Suitable for Hayward Salt Cell and Salt Chlorine Generator System with 15-Foot Cable.

You can use the two wire tel cord if available. When the unit reads AL-4 move the switch up to Super Chlorinate and back to Auto. IE9 and older versions are not supported.

Turns out some of these flow switches have misprinted directional arrows. If you dont have access to a VOM then perhaps the below might help. To change cell type cycle slide switch up to Super Chlorinate.

Back to Top No LEDs or LCD display screen. O HAYWARD Diagnosti Chlorinat Aut No Flow LED flashing or ON No Flow LED will flash for up to 60 seconds on start-up. Reset Average Salt Level 11.

From the Save As window. The fix was to go point directional arrows on cap the opposite of actual water flow. Hayward AqauRite Parts - httpbitly38uhdcpTeflon Tape - httpbitly38tErzwTroubleshooting Your Hayward Aqua Rite System - httpbitly2TMYlkRThe Flo.

Step 2 Ensure the flow switch valve is open. No Flow LED will be ON when there is a flow switch problem. Pump only Runs for 5 seconds If your Hayward pump runs for only.

That test bypasses tests for low flow and arrows installed wrong. 45 out of 5 stars. Check Salt Inspect Cell LED flashing or ON.

Installation requires 12 inches of straight pipe before flow switch. Check the wire for any damage. HCP 300 Series.

Hayward websites have been developed in compliance with standards for Internet Explorer 10 or later. Then give Hayward a call at 866-772-2100 to see what they say. If the No Flow LED is ON check if the flow switch is installed backward.

Step 2 Ensure the flow switch valve is open. AquaRite Hayward Goldline Aqua Rite Salt Generator FLO Flow Switch GLX-FLO-RP. Hayward Flow Control has been a leading manufacturer of industrial thermoplastic valves and process control products for more than 60 years.

If voltage is good go to step D. Power Generating Super Chlorinate Remotely Controlled -r No Flow Cheek Salt High Salt nSpect Cell If LED is ON check for flow switch installed backward. If you have questions regarding troubleshooting a problem installing this flow switch call 1-888-921-7665 for Technical support.

In fact Hayward was one of the originators of the first thermoplastic ball valves. Right click on the link of the file you wish to download. This generic replacement for the Hayward Goldline flow switch is relatively.

Alternatively continuity is close if sufficient water flow is detected. It takes about 30 seconds for the unit to settle back to the default reading. At proper Igniter temp a 4 second trial begins.

Return switch to AUTO. This flow switch is NOT compatible with any above ground spas. Since then we have remained committed to producing the highest quality products while providing outstanding service.

Push the diagnostics button until t - 15 t - 9 t -5 t - 3 appears. Check the wire for any damage. If this does not work turn the unit off again before trying any other troubleshooting techniques.

If there is adequate flow and the LED is still on check that the arrows on the flow switch on top of hex are pointing in the direction of flow.

Hayward Aqua Rite Troubleshooting Guide Poolsupplyworld Blog

Hayward Goldline Replacement Flow Switch Glx Flo Rp

Hayward Aquarite Swg Further Reading Trouble Free Pool

Hayward Goldline Replacement Flow Switch Glx Flo Rp

Hayward Aqua Rite Troubleshooting Guide Poolsupplyworld Blog

How To Recalibrate A Hayward Aqua Rite Turbo Cell Poolsupplyworld Blog

How To Troubleshoot A Hayward Aqua Rite Inyopools Com

Hayward Aqua Rite Troubleshooting Guide Poolsupplyworld Blog

One Minute Fix No Flow On Aqua Rite Hayward Salt Generator Youtube

Hayward Flow Switch Glx Flo Rp Pool Supply 4 Less

New Pool Owner Salt System Keeps Reporting No Flow My Salt Cell Isn T Generating Chlorine I Cleaned The Cell Changed The Flow Switch Decreased And Increased The Pressure From The Return I